天然气、沼气、垃圾填埋气和煤矿瓦斯是常见的能够应用于燃气内燃机的气体。除此之外,有一些工业领域内的废气含有可燃成分,例如氢气和一氧化碳等,矿热炉尾气就是其中一种能进入燃气内燃机发电的工业废气。这种废气虽然杂质多、热值低,但是经过净化处理以后可以进入燃气内燃机发电,从而实现变废为宝、节能减排,创造可观的经济效益。
Natural gas, biogas, landfill gas, and coal mine gas are common gases that can be applied to gas internal combustion engines. In addition, there are some industrial waste gases that contain combustible components, such as hydrogen and carbon monoxide. The tail gas of the submerged arc furnace is one of the industrial waste gases that can enter the gas internal combustion engine for power generation. Although this type of exhaust gas has many impurities and low calorific value, after purification treatment, it can enter the gas internal combustion engine for power generation, thereby realizing the transformation of waste into treasure, energy conservation and emission reduction, and creating considerable economic benefits.
矿热炉又称电弧电炉或电阻电炉。它主要用于还原冶炼矿石,碳质还原剂及溶剂等原料,主要生产硅铁,锰铁,铬铁、钨铁、硅锰合金等铁合金。矿热炉主要分为半密闭和密闭炉两种类型,其中密闭炉产生的尾气含有的可燃成分较多,能够用于燃气内燃机发电。
Mineral arc furnace, also known as electric arc furnace or resistance furnace. It is mainly used for reducing smelting ores, carbon reducing agents, solvents and other raw materials, and mainly produces ferroalloys such as ferrosilicon, ferromanganese, ferrochromium, ferrotungsten, and silicomanganese alloys. Mineral heat furnaces are mainly divided into two types: semi enclosed and enclosed furnaces. The exhaust gas generated by enclosed furnaces contains more combustible components and can be used for gas internal combustion engine power generation.
图1 某矿热炉尾气产生及利用流程
Figure 1 Production and Utilization Process of Tail Gas from a Mine Heating Furnace
在矿热炉生产铁合金的过程中产生的尾气(Furnace off gas,简称FOF)主要成分为CO,以及少量的 H2、 CO2等。其中一氧化碳(CO)气体是由于还原剂中存在碳而形成的,如果还原剂中含有挥发性碳氢化合物,则会形成氢气(H2)。过去,矿热炉尾气通常是直接燃烧后排放,而现在则可以通过高效的燃气内燃机发电,同时利用高温烟气的热能,使能源得到高效充分的利用。
The exhaust gas (FOF) generated during the production of ferroalloys in a submerged arc furnace is mainly composed of CO, as well as a small amount of H2, CO2, etc. Carbon monoxide (CO) gas is formed due to the presence of carbon in the reducing agent. If the reducing agent contains volatile hydrocarbons, hydrogen gas (H2) will be formed. In the past, the exhaust gas from submerged arc furnaces was usually discharged after direct combustion. However, now it can be generated through efficient gas internal combustion engines, while utilizing the heat energy of high-temperature flue gas to efficiently and fully utilize energy.
的热值通常只有天然气热值的1/3左右,也就是说相比于同级输出功率的天然气机型,FOF发电机组的进气量需要增大3倍以上。FOF的抗爆性与天然气也有显著区别,其甲烷指数(Methane Number,简称MN)只有天然气的大约60%左右,这意味着这种气体在内燃机气缸里面更容易发生爆震。所以,燃气发电机组需要通过传感器监测爆震的发生以调整机组的运行状态。
The calorific value of FOF power generation units is usually only about one-third of that of natural gas, which means that compared to natural gas models with the same level of output power, the intake volume of FOF power generation units needs to be increased by more than three times. The anti knock performance of FOF is also significantly different from that of natural gas, with its Methane Number (MN) only about 60% of that of natural gas, which means that this gas is more prone to detonation in internal combustion engine cylinders. Therefore, gas generator units need to monitor the occurrence of detonation through sensors to adjust the operating status of the unit.
![合金尾气发电机组](/uploadfile/2023/1006/20231006105501405.jpg)
另一方面,FOF燃烧时的层流火焰速度(Laminar Flame Speed,简称LFS)却比天然气快许多,这和气体里面氢气的含量比例有关。层流火焰速度是在层流前沿发生氧化反应的速度, 即未燃烧的混合气与火焰前沿之间的相对速度。根据麻省理工学院的研究资料,在当量比(Equivalence Ratio)为2时,5% H2和95% CO组成的混合气的LFS约为50cm/s,而 50% H2和50% CO组成的混合气的LFS可到160cm/s。鉴于FOF特殊的燃烧特性,燃气内燃机的进气系统和控制参数都需要特殊设计以适应其特性,同时还必须满足NOx的排放要求。
On the other hand, the laminar flame speed (LFS) during FOF combustion is much faster than natural gas, which is related to the proportion of hydrogen content in the gas. The laminar flame velocity is the rate at which oxidation reactions occur at the front of the laminar flow, that is, the relative velocity between the unburned mixture and the flame front. According to research data from the Massachusetts Institute of Technology, when the equivalence ratio is 2, the LFS of a mixture of 5% H2 and 95% CO is about 50cm/s, while the LFS of a mixture of 50% H2 and 50% CO can reach 160cm/s. Given the unique combustion characteristics of FOF, the intake system and control parameters of gas internal combustion engines require special design to adapt to their characteristics, while also meeting the NOx emission requirements.
颜巴赫的 DIA.NE XT4系统在气体质量波动时自动调整设置,因此能够适应复杂的运行情况。同时,颜巴赫的LEANOX稀薄燃烧控制技术能够实时控制氮氧化物NOx的排放,确保始终满足严苛的环保要求,使机组排气出口NOx达到250-500mg/Nm3(@5% O2),并且无需SCR等复杂的尾气后处理装置。新的颜巴赫资产管理系统myPlant则能实时监测、控制和预测机组的运行状态,并能提供前瞻性的维护保养建议。
Yanbach's advanced DIA. NE XT4 system automatically adjusts settings when gas quality fluctuates, thus being able to adapt to complex operating conditions. At the same time, Yanbach's LEANOX lean combustion control technology can control the emission of nitrogen oxide NOx in real-time, ensuring that strict environmental requirements are always met, so that the NOx at the exhaust outlet of the unit can reach 250-500mg/Nm3 (@ 5% O2), and there is no need for complex tail gas post-treatment devices such as SCR. The new Yanbach asset management system myPlant can monitor, control, and predict the operating status of the unit in real-time, and provide forward-looking maintenance recommendations.
燃气内燃机对气体的杂质含量要求
Requirements for impurity content of gas in gas internal combustion engines
尾气的成分和气量与炉子的运行参数有关,并受到原料质量、炉子控制和运行状态等因素的影响,所以通常会连续变化。采用气柜来减少气体热值和压力的波动,对于燃气内燃机发电非常重要。在炉子供气中断时,气柜还可以起到缓冲的作用。
The composition and gas volume of exhaust gas are related to the operating parameters of the furnace, and are influenced by factors such as raw material quality, furnace control, and operating status, so they usually change continuously. The use of gas cabinets to reduce fluctuations in gas calorific value and pressure is very important for gas internal combustion engine power generation. When the gas supply to the furnace is interrupted, the gas holder can also serve as a buffer.
进入内燃机前的FOF需要进行预处理,以满足气体质量要求。通常需要去除粉尘,以及多余的水分,还有焦油、硫及其他有害杂质等。硫、氨等成分的含量要求与燃气的热值相关,须根据实际热值确定上限值。下表是颜巴赫燃气内燃机对气体的一般质量要求。
The FOF before entering the internal combustion engine requires pre-treatment to meet the gas quality requirements. Usually, it is necessary to remove dust, excess water, tar, sulfur, and other harmful impurities. The content requirements of components such as sulfur and ammonia are related to the calorific value of the gas, and the upper limit value must be determined based on the actual calorific value. The following table shows the general quality requirements for gases in Yanbach gas internal combustion engines.
南非钛铁矿冶炼厂矿热炉尾气发电项目
South African Ilmenite Smelter Mine Furnace Tail Gas Power Generation Project
南非大的一家钛铁矿冶炼工厂于2012年采用了8台颜巴赫J620燃气发电机组,每台功率1,698 kW,总容量13.6 MW。所发出的电力并入公司11 kV内网,用于满足工厂部分电能需求。
A large titanium iron ore smelting plant in South Africa adopted 8 Yanbach J620 gas generator units in 2012, each with a power of 1698 kW and a total capacity of 13.6 MW. The electricity generated is integrated into the company's 11 kV internal network to meet some of the power needs of the factory.
工厂内有两个封闭的直流电弧炉,产生尾气主要成分为73% CO, 14.5% H2,以及少量CO2等。据测算,该项目平均每年大约可以减少84,432 吨二氧化碳排放,是联合国清洁发展机制CDM注册项目。
There are two enclosed DC arc furnaces in the factory, which produce tail gas mainly composed of 73% CO, 14.5% H2, and a small amount of CO2. According to calculations, the project can reduce carbon dioxide emissions by approximately 84432 tons per year on average, making it a registered CDM project under the United Nations Clean Development Mechanism.
挪威锰铁合金矿热炉尾气发电项目
Norwegian manganese iron alloy submerged arc furnace tail gas power generation project
北欧大的锰铁合金生产商采用了1台颜巴赫J620燃气发电机组用于矿热炉尾气发电 ,输出功率 1.5MW。尾气的主要成分为65% CO, 5% H2, 8% CO2等,低位热值(LHV)大约2.8 kWh/Nm3。项目于2020年调试完成并投入商业运行。
Nordic manganese iron alloy manufacturers have adopted one Yanbach J620 gas generator unit for generating tail gas from submerged arc furnaces, with an output power of 1.5MW. The main components of exhaust gas are 65% CO, 5% H2, 8% CO2, etc., with a low calorific value (LHV) of approximately 2.8 kWh/Nm3. The project was commissioned and completed in 2020 and put into commercial operation.
通过回收矿热炉尾气用于热电联供系统(CHP),减少工厂对来自电网的电力需求,节省了电能成本,而系统产生的高温烟气则用于冶炼前对矿石进行干燥。该工厂的目标是通过CHP的使用将工厂的能源效率提升40%。同时,该项目也因其在环境保护和节能减排方面的突出贡献,获得了挪威政府的大力支持。
By recycling the exhaust gas from the ore furnace for the combined heat and power supply system (CHP), the factory's demand for electricity from the power grid is reduced, saving electricity costs. The high-temperature flue gas generated by the system is used to dry the ore before smelting. The goal of the factory is to increase its energy efficiency by 40% through the use of CHP. At the same time, the project has also received strong support from the Norwegian government due to its outstanding contributions in environmental protection and energy conservation and emission reduction.
矿热炉尾气的发电应用充分利用了废气,将其转化为电能和热能,是冶炼行业节能减排和循环经济的榜样。通过对废气的利用变废为宝,在改善环保排放的同时创造新的价值,节约了企业的运营成本。颜巴赫在该领域拥有丰富的经验,其发电机组产品单机功率大,发电效率高,调试周期短,可靠性好,能够有效帮助用户获得可观的收益和显著的碳减排效果。在我国“双碳”战略目标的大背景下,随着对冶金行业环保要求的不断提高,矿热炉尾气的高效利用将拥有广阔的发展前景。
The power generation application of the tail gas of the submerged arc furnace fully utilizes the exhaust gas, converting it into electrical and thermal energy, and is an example of energy conservation, emission reduction, and circular economy in the smelting industry. By utilizing exhaust gas to turn waste into treasure, we can improve environmental emissions while creating new value and saving operating costs for enterprises. Yan Bach has rich experience in this field. His generator set products have high single unit power, high power generation efficiency, short debugging cycle, and good reliability, which can effectively help users achieve considerable profits and significant carbon reduction effects. Against the backdrop of China's "dual carbon" strategic goal, with the continuous improvement of environmental protection requirements for the metallurgical industry, the efficient utilization of tail gas from submerged arc furnaces will have broad development prospects.
本文的精彩内容由
合金尾气发电机组提供知识提供,本网站还有很多的精彩内容,更多的内容您可以点击进入:
我们有专门的客服为您解答问题
The exciting content of this article is provided by the knowledge of alloy exhaust gas generator sets. There are also many exciting content on this website, and you can click to enter more content: We have dedicated customer service to answer your questions