Large generator set is the most widely used power generation equipment in the market, which alleviates the tension of power consumption and brings convenience to people. The following is a brief analysis of the engine oil filter element by the generator manufacturer:

油滤芯结构简单，其内部滤纸和一些重要的部分从外观也很难区别。所以各种高仿滤芯层出不穷，而且价格低廉，故而有些用户为了省钱就去购买伪劣品。机油滤芯一定要选择正规的，如果没有质量保证的滤芯使用以后将会引起机组故障，导致机组受损，一旦机器内部混入杂质，那可就得不偿失了。

The structure of the oil filter element is simple, and it is difficult to distinguish its internal filter paper and some important parts from their appearance. Therefore, all kinds of high imitation filter elements emerge in endlessly, and the price is low. Therefore, some users buy fake and shoddy products in order to save money. The regular brand of engine oil filter element must be selected. If there is no quality assurance filter element, it will cause unit failure and damage. Once impurities are mixed into the machine, the gain is not worth the loss.

机油滤芯更换步骤：

Oil filter element replacement steps:

步：排出废机油

Step 1: drain the waste engine oil

先把油箱里的废机油排出，在油底壳下方放置旧油容器，打开放油螺栓，排出废机油。排放机油的时候尽量让机油多滴下一段时间，要保证废油排放干净。(机油通过使用，会产生很多杂质，如果在更换的时候排放不干净，容易堵塞油路，造成供油不畅，造成结构件磨损。

First drain the waste oil in the oil tank, place the old oil container under the oil pan, open the oil drain bolt and drain the waste oil. When draining the engine oil, try to let the engine oil drip for a period of time, and ensure that the waste oil is drained clean. (the engine oil will produce a lot of impurities through use. If it is not discharged cleanly during replacement, it is easy to block the oil circuit, resulting in poor oil supply and wear of structural parts.

第二步：拆除旧的机油滤芯

Step 2: remove the old engine oil filter element

把旧油容器移至机滤下方，拆下旧的滤芯。注意不要让废油弄脏机器内部。

Move the old oil container under the filter and remove the old filter element. Be careful not to let waste oil dirty the inside of the machine.

第三步：机油滤芯安装前的准备工作

Step 3: preparation before installation of oil filter element

康姆勒发电机厂家技术专家告诉用户更换新的机滤用不用先往滤芯里面注满机油。

The technical expert from the manufacturer of komler generator told the user to replace the new filter without filling the filter element with engine oil first.

第四步：安装新的机油滤芯

Step 4: install a new oil filter element

检查机油滤芯安装位置的出油口，清理上面的脏物和残留的废油。安装前，先在出油口位置套上密封环，然后把新的机滤慢慢的拧上去，机滤不要拧的太紧，一般情况下是用手拧紧以后，再用扳手拧3/4圈就可以了。注意装新滤芯的时候，使用扳手拧不要用力过大，否则容易损坏滤芯内部的密封圈，造成密封效果变差，起不到过滤效果!

Check the oil outlet at the installation position of the oil filter element and clean the dirt and residual waste oil on it. Before installation, first put a sealing ring on the oil outlet, and then screw the new filter slowly. Do not screw the filter too tightly. Generally, after tightening by hand, use a wrench to screw it for 3 / 4 turn. Note: when installing a new filter element, use a wrench and do not use too much force, otherwise it is easy to damage the sealing ring inside the filter element, resulting in poor sealing effect and no filtering effect!

第五步：往机油油箱加注新的机油

Step 5: fill the oil tank with new oil

将新机油注入机油油箱，必要时，要使用漏斗，防止将机油倒在发动机外部。加注完以后，再次检查发动机下部是否有泄漏。

Fill the oil tank with new oil. If necessary, use a funnel to prevent the oil from pouring out of the engine. After filling, check the lower part of the engine again for leakage.

以上就是今天小编给大家提供的精彩内容，更多的精彩内容请点击进入我们的官方网站：机油滤芯http:

The above is the wonderful content provided by Xiaobian today. For more wonderful content, please click to enter our official website: engine oil filter element http: